What Causes Air in RV Water System?

RV water systems are essential for providing fresh water for drinking, cooking, and bathing. However, air can sometimes get trapped in these systems, which can cause a number of problems. This blog post will discuss the causes of air in RV water systems, as well as how to fix it.

Causes of Air in RV Water Systems

There are a number of reasons why air can get trapped in RV water systems. Some of the most common causes include:

• Leaking pipes or connections. If there are any leaks in your RV's water system, air can get in through the cracks.
• Rapid temperature changes. Rapid water temperature changes can cause air to be trapped in the system.
• Improper installation. If your RV's water system was not installed properly, it can lead to air getting trapped in the system.
• Frozen pipes. If the water in your RV's pipes freezes, it can cause the pipes to expand and crack, which can allow air to get in.

Problems Caused by Air in RV Water Systems

When air gets trapped in an RV water system, it can cause a number of problems, such as:

• Reduced water pressure. Water pressure can be reduced in the system if there is trapped aiur present.
• Spitting or sputtering water. Air in the system can cause the water to come out of the faucets in a sputtering or spitting manner.
• Air bubbles in the water. Air bubbles can form in the water if there is air in the system, which can make it look cloudy or discolored.
• Damage to the water pump. Damage can be placed on the water pump if it is put under too much strain frokm air being trapped in the system.

How to Fix Air in RV Water System

There are a number of things that you can do to fix air in your RV water system. Some of the most common fixes include:

• Bleed the air from the system. To bleed the air from the system, open the faucet that is furthest away from the water pump and let the water run until the air bubbles stop coming out.
• Replace any leaking pipes or connections. If there are any leaking pipes or connections in your RV's water system, replace them immediately.
• Install a water filter. A water filter can help to remove air from your RV's water system.
• Winterize your RV. Winterizing will help to prevent the water in your pipes from freezing and cracking.

Preventing Air in RV Water System

By following the tips in this blog post, you can help to prevent air from getting trapped in your RV water system and avoid the problems that it can cause.

• Inspect your RV's water system regularly for leaks. If you find any leaks, fix them immediately.
• Don't let the water in your RV's pipes freeze. If you are going to be storing your RV for the winter, be sure to winterize it properly.
• Install a water filter. A water filter can help to remove air from your RV's water system.

Why Bleed Your RV Water Pump System?

Bleeding your RV water pump system is an essential maintenance task that ensures your water pump works efficiently and effectively. If air enters the water pump system, it can cause the pump to lose its prime, leading to poor water flow and pressure. Therefore, bleeding your RV water pump system is crucial to ensure the longevity of your RV water pump.

When to Bleed Your RV Water Pump System?

You should bleed your RV water pump system every time you drain and refill your RV's water system, especially after winterizing your RV. You should also bleed your RV water pump system if you notice poor water flow and pressure when using the faucets or shower.

Tools Required to Bleed Your RV Water Pump System

• Phillips head screwdriver
• Wrench
• A bucket to catch water

Steps to Bleed Your RV Water Pump System

Step 1: Turn off the Water Pump

Before bleeding your RV water pump system, turn off the water pump and disconnect the RV from the shore water connection.

Step 2: Locate the Water Pump

The water pump is usually located near the freshwater tank, and it is connected to the RV's water system. Use the wrench to loosen the water pump's fitting and remove the hose connected to the pump's inlet side.

Step 3: Drain the Water Pump

The bucket should now be placed below the water pump. Now turn on the faucet to allow all water in the system to drain out of the pump. Let the water drain until only air comes out of the hose.

Step 4: Reconnect the Hose

After draining the water pump, reconnect the hose to the pump's inlet side and tighten the fitting with a wrench.

Step 5: Turn On the Water Pump

The next step is to turn on the water pump and simply wait for it to build pressure. After that is done, It will be time to allow all the air to exit the system.